Vario gas cooktop 400 Series
VG 491
-- 5 burners with an output of up to
18 kW.
-- Fully
fully electronic flame regulation on 12 levels.
-- ultra-precise flame regulation
ultra-precise flame regulation.
-- Electronic flame control
with automatic re-ignition in case
electronic flame control with automatic re-ignition in case of flame failure.
-- Simmer function at minimum
-- intensity.
-- Solid grills with flat surface.
-- Solid stainless steel control knob.
stainless steel control knob.
-- Precise workmanship of steel with
3 mm thick.
-- Possible countertop installation
or flush-mounted.
-- Perfect combination with all Vario 400
Perfect combination with all Vario 400 series appliances.
Cooking zones
VG 491 111F
1 multi-crown Wok burner
(300 - 5800 W), suitable for Wok pans and
pans ø max. 32 cm.
2 ultra-rapid crown burners
(165 - 4000 W), suitable for
pots of ø max. 28 cm.
2 multi-crown burners (165 -
2000 W), suitable for pots of ø max. 24 cm.
VG 491 211
1 Wok multi-crown burner
(300 - 6000 W), suitable for Wok pans and
pans ø max. 32 cm.
2 ultra-rapid crown burners
multiple crown burners (165 - 4000 W), suitable for
pots of ø max. 28 cm.
2 multi-crown burners (165 -
2000 W), suitable for pots of ø max. 24 cm.
Operation
Steel knobs with ring
light ring and screen printing for cooking zones
and power levels.
All the comfort of automatic
automatic. Immediate ignition of the
flame with a single gesture.
Fully electronic control with
12 levels for exact regulation
temperature and slow cooking function.
slow cooking function.
Features
Simmer function for melting and
keeping warm with flame on/off.
deactivation of the flame.
Brass burners.
Three-part cast-iron grill with
flat surface.
Safety
Electronic flame control with
automatic re-ignition in the event of
accidental extinguishing.
Safety thermocouple.
Residual heat indication.
Automatic safety shutdown.
Installation precautions
Depending on the type of installation
(surface-mounted or flush-mounted, with or without cover), the
cover), the position of the recess
recess and knob may vary.
vary.
Align the knobs with the burners.
Always comply with the drawings regarding
installation of the knobs.
If the panel is thicker than 23 mm
provide a space on the rear side
rear side.
Important: any hobs
(VG, VP and VR), if equipped with a
stainless steel lid, may only be
only be installed in individual
individual built-in compartments. Therefore, it is not
possible to combine several
appliances in a single hole. If you
several luminaires in individual
slots, the minimum distance between them
must be 50 mm.
If several luminaires of the
Vario 400 series without cover, it is
required instead is the use
of the connecting element VA 420
between the various luminaires. Depending on the type of
of installation, the corresponding
corresponding connecting element.
connection element.
The load-bearing capacity and stability, in particular
in the case of thin worktops, must
be supported by appropriate
substructures. Take into
consideration of the weight of the appliance
and additional loads.
Additional installation instructions
flush:
Installation is possible in floors made of
stone, synthetic or solid wood.
The thermal resistance
thermal resistance and watertightness of the edges
of the notch. Regarding other
materials, please consult the
manufacturer of the worktop.
The groove must be continuous and
uniform, so as to ensure the correct
positioning of the unit on the
gasket. Do not use a
discontinuous coating.
The width of the joint may vary
due to dimensional tolerances of the
combinations and the notch on the surface
working surface.
If several appliances are installed in
individual niches, provide a space
of at least 50 mm between the niches.
Special nozzles can be ordered separately.
The electrical connection is
indispensable for the operation
of the unit.
Air supply from above.
Installation without intermediate floor.
Provide a non-flammable material for the rear wall and
laths a non-flammable and heat-resistant material.
heat-resistant material.
Leave a minimum distance of 30 cm between
the floor and heat-sensitive surfaces
or apply thermal insulation.
Can be fitted in 90 cm base units.
Not recommended in combination with the
VL 414 extraction centre because of the
excessive distance between the central burner
central burner and the hood itself.
With a total absorption of more than 11
kW, the local ventilation
local regulations regarding ventilation
of the room, chamber surface and
the combination with extractor hoods
or recirculation hoods. The minimum distance between the
gas cooker hob (with more than 11 kW) and
the extractor hood is 70 cm.
The appliance can be installed
from above.
Appliance weight 32 kg.
Connection values
Total gas consumption 17.8 /18.0 kW.
Total power consumption 15.0 W.
Connection cable 1.4 m with
Schuko plug.
