gaggenau VG415111F

Wok gas hob

Tax included

Wok gas hob

Vario 400 Series

VG 415

-- Powerful multiple crown flame

up to 6 kW.

-- Fully

fully electronic flame regulation in 12 levels.

-- Ultra precise flame regulation.


-- Electronic flame control

with automatic re-ignition in case

electronic flame control with automatic re-ignition in case of flame failure.

-- Simmer function at minimum


-- Solid stainless steel control knob.

stainless steel control knob.

-- Precise stainless steel workmanship with

3 mm thick.

-- Possible surface-mounting

or flush-mounted.

-- Perfect combination with all Vario 400

Perfect combination with all Vario 400 series appliances.

Cooking zones

VG 415 111F

1 multi-crown Wok burner

(300 W - 5800 W), suitable for pans/

pans up to ø 32 cm.

VG 415 211

1 multi-crown Wok burner

(300 W - 6000 W), suitable for pans/ pots up to ø 32 cm.

pans/ pots up to ø 32 cm.


Steel knobs with ring

light ring and silkscreen printing for cooking zones

cooking zones and power levels.

All the comfort of automatic

automatic. Immediate ignition of the

flame with a single gesture.

Fully electronic control with

12 levels for exact regulation

temperature and slow cooking function.

slow cooking.


Simmer function for melting and

keeping warm with flame on/off.

deactivation of the flame.

Cast-iron grill.

Brass burners.


Electronic flame control with

automatic re-ignition in case of

accidental extinguishing.

Safety thermocouple.

Residual heat indication.

Automatic safety shutdown.

Installation precautions

Depending on the type of installation (surface

or flush-mounted, with or without cover)

cover), the position of the recess

recess and knob may vary.


Always comply with the drawings relating

installation of the knobs. If the

panel is thicker than 23 mm

provide a space on the rear side

rear side.

If installing with cover VA 440

take into account the additional space

additional space required for the depth

Important: any hobs

(VG, VP and VR), if fitted with a

stainless steel lid, can only be installed

only be installed in individual built-in compartments.

individual built-in compartments. Therefore, it is not

possible to combine several

appliances in a single hole. If you

several luminaires in individual

slots, the minimum distance between them

must be 50 mm.

If several luminaires of the

Vario 400 series without cover, it is

required instead is the use

of the connecting element VA 420

between the various luminaires. Depending on the type of

of installation, the corresponding

corresponding connecting element.

The load-bearing capacity and stability, in particular

in the case of thin worktops, must

be supported by appropriate

substructures. Take into

consideration of the weight of the appliance

and additional loads.

Additional installation instructions


Installation is possible in floors made of

stone, synthetic or solid wood.

The thermal resistance

thermal resistance and watertightness of the edges

of the notch. Regarding other

materials, please consult the

manufacturer of the worktop.

The groove must be continuous and

uniform, so as to ensure the correct

positioning of the unit on the

gasket. Do not use a

discontinuous coating.

The width of the joint may vary

due to dimensional tolerances of the

combinations and the notch on the surface

working surface.

If several units are installed in

individual recesses provide a space

of at least 50 mm between the recesses.

Special nozzles can be ordered separately.

The electrical connection is

indispensable for the operation

of the unit.

Air supply from above.

Installation without intermediate floor.

Provide a non-flammable material for the rear wall and

laths a non-flammable and heat-resistant material.

heat-resistant material.

Leave a minimum distance of 150 mm between the

floor and heat-sensitive surfaces

or apply thermal insulation.

In the case of a combination with floor

suction unit, it is always

necessary to position the unit

between 2 VL 414.

If positioned close to the VL 414

downdraft ventilation VL 414, it is

the use of the deflector AA 414 is necessary

to ensure maximum performance and

safety of the hob.

With a total absorption of more than 11

kW, the local ventilation

local regulations regarding ventilation

of the room, chamber surface and

the combination with extractor hoods

or recirculation hoods. The minimum distance between the

gas cooker hob (with more than 11 kW) and

the extractor hood is 70 cm.

The appliance is equipped with springs

fixing springs that lock the hob after

insertion from above.

Appliance weight 16 kg.

Connection values

Total gas consumption 5.8/6.0 kW.

Total power consumption 15.0 W.

Connection cable 1.4 m with

Schuko plug.