Gaggenau VG491111F

Vario gas cooktop 400 Series

€4,618.90
Tax included

Vario gas cooktop 400 Series

VG 491

-- 5 burners with an output of up to

18 kW.

-- Fully

fully electronic flame regulation on 12 levels.

-- ultra-precise flame regulation

ultra-precise flame regulation.

-- Electronic flame control

with automatic re-ignition in case

electronic flame control with automatic re-ignition in case of flame failure.

-- Simmer function at minimum

-- intensity.

-- Solid grills with flat surface.

-- Solid stainless steel control knob.

stainless steel control knob.

-- Precise workmanship of steel with

3 mm thick.

-- Possible countertop installation

or flush-mounted.

-- Perfect combination with all Vario 400

Perfect combination with all Vario 400 series appliances.

Cooking zones

VG 491 111F

1 multi-crown Wok burner

(300 - 5800 W), suitable for Wok pans and

pans ø max. 32 cm.

2 ultra-rapid crown burners

(165 - 4000 W), suitable for

pots of ø max. 28 cm.

2 multi-crown burners (165 -

2000 W), suitable for pots of ø max. 24 cm.

VG 491 211

1 Wok multi-crown burner

(300 - 6000 W), suitable for Wok pans and

pans ø max. 32 cm.

2 ultra-rapid crown burners

multiple crown burners (165 - 4000 W), suitable for

pots of ø max. 28 cm.

2 multi-crown burners (165 -

2000 W), suitable for pots of ø max. 24 cm.

Operation

Steel knobs with ring

light ring and screen printing for cooking zones

and power levels.

All the comfort of automatic

automatic. Immediate ignition of the

flame with a single gesture.

Fully electronic control with

12 levels for exact regulation

temperature and slow cooking function.

slow cooking function.

Features

Simmer function for melting and

keeping warm with flame on/off.

deactivation of the flame.

Brass burners.

Three-part cast-iron grill with

flat surface.

Safety

Electronic flame control with

automatic re-ignition in the event of

accidental extinguishing.

Safety thermocouple.

Residual heat indication.

Automatic safety shutdown.

Installation precautions

Depending on the type of installation

(surface-mounted or flush-mounted, with or without cover), the

cover), the position of the recess

recess and knob may vary.

vary.

Align the knobs with the burners.

Always comply with the drawings regarding

installation of the knobs.

If the panel is thicker than 23 mm

provide a space on the rear side

rear side.

Important: any hobs

(VG, VP and VR), if equipped with a

stainless steel lid, may only be

only be installed in individual

individual built-in compartments. Therefore, it is not

possible to combine several

appliances in a single hole. If you

several luminaires in individual

slots, the minimum distance between them

must be 50 mm.

If several luminaires of the

Vario 400 series without cover, it is

required instead is the use

of the connecting element VA 420

between the various luminaires. Depending on the type of

of installation, the corresponding

corresponding connecting element.

connection element.

The load-bearing capacity and stability, in particular

in the case of thin worktops, must

be supported by appropriate

substructures. Take into

consideration of the weight of the appliance

and additional loads.

Additional installation instructions

flush:

Installation is possible in floors made of

stone, synthetic or solid wood.

The thermal resistance

thermal resistance and watertightness of the edges

of the notch. Regarding other

materials, please consult the

manufacturer of the worktop.

The groove must be continuous and

uniform, so as to ensure the correct

positioning of the unit on the

gasket. Do not use a

discontinuous coating.

The width of the joint may vary

due to dimensional tolerances of the

combinations and the notch on the surface

working surface.

If several appliances are installed in

individual niches, provide a space

of at least 50 mm between the niches.

Special nozzles can be ordered separately.

The electrical connection is

indispensable for the operation

of the unit.

Air supply from above.

Installation without intermediate floor.

Provide a non-flammable material for the rear wall and

laths a non-flammable and heat-resistant material.

heat-resistant material.

Leave a minimum distance of 30 cm between

the floor and heat-sensitive surfaces

or apply thermal insulation.

Can be fitted in 90 cm base units.

Not recommended in combination with the

VL 414 extraction centre because of the

excessive distance between the central burner

central burner and the hood itself.

With a total absorption of more than 11

kW, the local ventilation

local regulations regarding ventilation

of the room, chamber surface and

the combination with extractor hoods

or recirculation hoods. The minimum distance between the

gas cooker hob (with more than 11 kW) and

the extractor hood is 70 cm.

The appliance can be installed

from above.

Appliance weight 32 kg.

Connection values

Total gas consumption 17.8 /18.0 kW.

Total power consumption 15.0 W.

Connection cable 1.4 m with

Schuko plug.