Wok gas hob
Vario 400 Series
VG 415
-- Powerful multiple crown flame
up to 6 kW.
-- Fully
fully electronic flame regulation in 12 levels.
-- Ultra precise flame regulation.
flame.
-- Electronic flame control
with automatic re-ignition in case
electronic flame control with automatic re-ignition in case of flame failure.
-- Simmer function at minimum
intensity.
-- Solid stainless steel control knob.
stainless steel control knob.
-- Precise stainless steel workmanship with
3 mm thick.
-- Possible surface-mounting
or flush-mounted.
-- Perfect combination with all Vario 400
Perfect combination with all Vario 400 series appliances.
Cooking zones
VG 415 111F
1 multi-crown Wok burner
(300 W - 5800 W), suitable for pans/
pans up to ø 32 cm.
VG 415 211
1 multi-crown Wok burner
(300 W - 6000 W), suitable for pans/ pots up to ø 32 cm.
pans/ pots up to ø 32 cm.
Operation
Steel knobs with ring
light ring and silkscreen printing for cooking zones
cooking zones and power levels.
All the comfort of automatic
automatic. Immediate ignition of the
flame with a single gesture.
Fully electronic control with
12 levels for exact regulation
temperature and slow cooking function.
slow cooking.
Features
Simmer function for melting and
keeping warm with flame on/off.
deactivation of the flame.
Cast-iron grill.
Brass burners.
Safety
Electronic flame control with
automatic re-ignition in case of
accidental extinguishing.
Safety thermocouple.
Residual heat indication.
Automatic safety shutdown.
Installation precautions
Depending on the type of installation (surface
or flush-mounted, with or without cover)
cover), the position of the recess
recess and knob may vary.
vary.
Always comply with the drawings relating
installation of the knobs. If the
panel is thicker than 23 mm
provide a space on the rear side
rear side.
If installing with cover VA 440
take into account the additional space
additional space required for the depth
Important: any hobs
(VG, VP and VR), if fitted with a
stainless steel lid, can only be installed
only be installed in individual built-in compartments.
individual built-in compartments. Therefore, it is not
possible to combine several
appliances in a single hole. If you
several luminaires in individual
slots, the minimum distance between them
must be 50 mm.
If several luminaires of the
Vario 400 series without cover, it is
required instead is the use
of the connecting element VA 420
between the various luminaires. Depending on the type of
of installation, the corresponding
corresponding connecting element.
The load-bearing capacity and stability, in particular
in the case of thin worktops, must
be supported by appropriate
substructures. Take into
consideration of the weight of the appliance
and additional loads.
Additional installation instructions
flush:
Installation is possible in floors made of
stone, synthetic or solid wood.
The thermal resistance
thermal resistance and watertightness of the edges
of the notch. Regarding other
materials, please consult the
manufacturer of the worktop.
The groove must be continuous and
uniform, so as to ensure the correct
positioning of the unit on the
gasket. Do not use a
discontinuous coating.
The width of the joint may vary
due to dimensional tolerances of the
combinations and the notch on the surface
working surface.
If several units are installed in
individual recesses provide a space
of at least 50 mm between the recesses.
Special nozzles can be ordered separately.
The electrical connection is
indispensable for the operation
of the unit.
Air supply from above.
Installation without intermediate floor.
Provide a non-flammable material for the rear wall and
laths a non-flammable and heat-resistant material.
heat-resistant material.
Leave a minimum distance of 150 mm between the
floor and heat-sensitive surfaces
or apply thermal insulation.
In the case of a combination with floor
suction unit, it is always
necessary to position the unit
between 2 VL 414.
If positioned close to the VL 414
downdraft ventilation VL 414, it is
the use of the deflector AA 414 is necessary
to ensure maximum performance and
safety of the hob.
With a total absorption of more than 11
kW, the local ventilation
local regulations regarding ventilation
of the room, chamber surface and
the combination with extractor hoods
or recirculation hoods. The minimum distance between the
gas cooker hob (with more than 11 kW) and
the extractor hood is 70 cm.
The appliance is equipped with springs
fixing springs that lock the hob after
insertion from above.
Appliance weight 16 kg.
Connection values
Total gas consumption 5.8/6.0 kW.
Total power consumption 15.0 W.
Connection cable 1.4 m with
Schuko plug.
